Welding is a family of methods used for joining two workpieces; steel in the case of SSAB. Usually a single heat source, normally an electrical arc, locally melts the two workpieces to form a common liquid pool. When the steel solidifies, the pieces are joined. In many cases, a special steel rod or wire (consumable, filler) is melted into the weld pool to get a good weld joint.
Workpieces can be preheated in a furnace with an oxy-fuel flame, with electrical heating mats or with electrical induction. It is crucial not to exceed the maximum temperatures given in the data sheet for the steel grade to be welded. Too high a temperature may negatively affect the properties of the steel.
Steel workpieces can be preheated in a furnace with an oxy-fuel flame, with electrical heating mats or with electrical induction. It is crucial not to exceed the maximum temperatures given in the data sheet for the steel grade involved. Too high a temperature may negatively affect the properties of the steel.
| Steel grade | Holding temperature [ºC] | Heating and cooling rate [ºC/h] | Holding time [min/mm] | Suitable time at the holding temperature [h] |
| Strenx® 700 | 550-580 ºC | 100 | 2 min/mm of single plate thickness, min 1 h | 1-6 |
| Strenx® 900 | 520-550 ºC | 100 | 2 min/mm of single plate thickness, min 1 h | 1-6 |
| Strenx® 960 | 520-550 ºC | 100 | 2 min/mm of single plate thickness, min 1 h | 1-6 |
| Hardox® HiTuf | 510-530 ºC | 100 | 2 min/mm of single plate thickness, min 1 h | 1-6 |
| Hardox® HiTemp | 450-480 ºC | 100 | 2 min/mm of single plate thickness, min 1 h | 1-6 |
Source: SSAB Welding Handbook
A rule of thumb is a maximum of 5 ml hydrogen per 100 g weld metal. However, this is in practice not possible to measure. The hydrogen content in solid wires for MAG welding is typically around 1.5-2 ml hydrogen per 100 g weld metal, while cored wires can pick up moisture in the flux which might increase to higher values per 100 g weld metal. Keep all consumables dry and warm, in particular flux-covered and flux-core ones. Packages should be opened shortly before use.
Shielding gas protects the liquid weld pool from nitrogen and oxygen in the air. Shielding gases are usually different mixtures of argon and carbon dioxide affecting the welding process and result. Shielding gases for Hardox® and Strenx® steels are the same as for other low-alloyed steels.
| Welding method | Arc type | Position | Shielding gas [weight %] |
| MAG, solid wire | Short arc | All positions | 18-25% CO2, rest Argon |
| MAG, cored wire | Short arc | All positions | 18-25% CO2, rest Argon |
| MAG, solid wire | Spray arc | Horizontal (PA, PB, PC) | 15-20% CO2, rest Argon |
| MAG, MCAW | Spray arc | All positions | 15-20% CO2, rest Argon |
| MAG, MCAW | Spray arc | Horizontal (PA, PB, PC) | 15-20% CO2, rest Argon |
| Robotic and automatic Mag | Spray arc | Horizontal (PA, PB, PC) | 8-18% CO2, rest Argon |
| TIG | Spray arc | All positions | 100% Argon |
Source: SSAB Welding Handbook
Hardfacing is a procedure where a harder material is welded to the base metal surface to create a protective layer. The method can be applied to all SSAB steels, but for the hardest ones, a soft buffer layer must first be welded on the base plate to reduce the risk of cold cracking into the base plate. All types of conventional welding processes can be used for both the buffer layer and the hardfacing layer.
Too much heat input will alter the mechanical properties of the welded joint (base material in too big a volume) while too little heat input may result in a lack of fusion. SSAB recommends the SSAB WeldCalc app to calculate proper welding parameters.
Hydrogen cracks in welded joints can form due to the concentration of hydrogen in the material close to the weld, as hydrogen embrittles the material. Hydrogen atoms in a hot welded joint will diffuse and collect at “comfortable” spots, e.g. microdefects in the microstructure. Hydrogen gets trapped when the joint cools. Cracks can initiate from those hydrogen traps after hours or even days. The inevitable residual stresses will elongate the cracks. High hardness and alloying make steels more sensitive to hydrogen cracking.
There are many factors that could cause a welded joint to fail. The most common ones are defects in the form of physical discontinuities, poor microstructure, and residual stresses. There are various reasons behind those factors, including choice of design, joint type, joint geometry, welding process, heat input, preheating, and welding consumables.
There are many possible welding defects. Some of the more common ones include:
More information on the above defects can be found in the SSAB Welding Handbook.
The information in this report is only applicable to SSAB’s products and should not be applied to any other products than original SSAB products.
This report provides general results and recommendations for SSAB steel products. This report is subject to SSAB’s Terms of Use. It shall be the user's responsibility to verify that the information contained herein is correct and is suitable to be used for the particular purpose and application of the user. The report is intended to be used by professional users only who possess adequate expertise, qualification and knowledge for the safe and correct use of the results and recommendations in this report. This report is provided “as is”. The use of the report is at user’s own discretion and risk and that users will be solely responsible for any use of this report. SSAB disclaims any liability for the content or potential errors of this report, including but not limited to warranties and condition of merchantability or fitness for a particular purpose or suitability for individual applications. SSAB shall not be liable for any kind of direct or indirect damages and/or costs related to or arising therefrom, whether special, incidental, consequential or directly or indirectly related to the use of, or the inability to use, the report or the content, information or results included therein.